Forbo Sustain 1195 Sheet and tile adhesive
RECOMMENDED FOR USE WITH:
- Marmoleum® Sheet, Walton, Marmoleum® Decibel, Marmoleum® Composition Sheet (MCS), Marmoleum® Sport,
- Corkment Underlayment
- Marmoleum® Modular, Marmoleum® Composition Tile (MCT)
- Flotex® Sheet
- Flotex® Tile and Allura Flex (permanent applications)
- Allura, Eternal (Material, Wood), Eternal Step (Original, SR, Wood), Eternal Decibel
Sustain 1195 Marmoleum Sheet & Tile Adhesive Tech Sheet
1 gallon: 125 sq ft
• SCS-Certified 20% Post-Consumer Recycled Content (PCC)
• Packaged in biodegradable plastic pails
• Dual Acrylic Polymer
• Not flammable; 100% Solvent free
• Storage: Freeze-thaw stable: 1 cycle at 20o F. If the pail is opened and found to be frozen, let it set closed and undisturbed at room temperature until thawed. DO NOT try to mix frozen adhesive.
• Shelf life: 1 year in unopened container
• Appearance and Odor: Green paste with little or no odor
• VOC Emissions: 0 grams per liter (calculated per CA South Coast Rule 1168)
• Spread Rate: Approximately 125 square feet per gallon
• Available in one and four gallon units
1. Areas to receive material should be clean, fully enclosed and weather tight. The permanent HVAC should be fully
operational and controlled and set at a minimum temperature 65º F (18.3º C). If this is not possible, the areas
should be acclimated and controlled by means of temporary HVAC to the service level conditions expected during
occupancy. The temperature should range from 75º F ± 10º F (23.9º C ± 5.5º C) with a
40% – 65% ambient relative humidity. These conditions MUST be established at least seven days prior to beginning
the installation, maintained during the installation, and continued for at least seven days following the installation.
2. The substrate must be free of all foreign materials including, but not limited to, dust, solvent, paint, wax, oil, grease,
residual adhesive, adhesive removers, film-forming curing compounds, silicate penetrating curing compounds,
sealing, hardening, or parting compounds, alkaline salts, excessive carbonation or laitance, mold, mildew, and
other foreign materials that might affect the quality of bond to the substrate.
3. Thoroughly stir the adhesive before use.
IMPORTANT! The adhesive MUST be mixed mechanically using a drill. The drill should be operated at low speed
and IN REVERSE. Using the mixing paddle in this way will pull material up from the bottom of the pail rather than
pulling material exposed to the air from the top down, entrapping air. The low speed limits air entrapment into the
4. Trowel recommendation: 1/16” x 1/32” x 1/32” fine notch trowel. Replace the trowel when proper coverage is no
5. Spread the Forbo EZ-ON 100™ Adhesive onto the floor. The adhesive will self-level as it sets up on the substrate.
6. The open time and working time of Forbo EZ-ON 100™ Adhesive will vary depending on the ambient temperature
and ambient relative humidity of the space. If any of these factors fall outside of the recommended ranges for use,
the gel time of the adhesive will be affected. Follow the chart below for open time (shown in hours) and working
time (shown in minutes). Fully gelled adhesive will not provide wet transfer when touched with a finger. A slight
oily residue may be noticed when touching, however the adhesive will not displace under pressure from the finger.
IMPORTANT! When the adhesive is touched at the optimal open time, no wet transfer of adhesive to the finger
should occur, although there will be a slight oily residue noticed on the finger. As the adhesive cures, this residue
7. Once the Forbo EZ-ON 100™ Adhesive has fully gelled, the flooring may be installed. Be sure to use reference marks
to lay out flooring, as the Forbo EZ-ON 100™ Adhesive has a very strong initial grab and the repositioning of the
flooring once laid into the adhesive may be difficult.
8. Immediately roll the flooring in all directions using a 100 lb. roller to ensure that flooring has made complete
contact with the adhesive. Additional rolling is required during installation to ensure that the material is flat and
9. The use of a three-section wall roller or steel seam roller is required at walls, under toe kicks or anywhere the full
weight of a 100 lb. roller cannot access or be applied.
10. Remove any adhesive residue immediately with a clean white cloth with Forbo Adhesive Remover or mineral
spirits. The area must then be rinsed with clean, cool water to remove all residue from the floor.
Marmoleum Frequently asked Questions
Lots of people ask the simple question, What is Marmoleum anyway?
First of all, it is a four syllable word that is slang for marbleized linoleum. Made from linseed or flaxseed oil, natural pigments, limestone dust, wood fibers and resins and then pressed onto a jute backing it is a great alternative to vinyl flooring. People who are sensitive to plastics and their off-gassing like it because it is not pvc or rubber and contains no acrylics. It also doesn’t require the use of volatile adhesives or contact cements to install it.
I ordered samples of Marmoleum and I heard that the color will be very different when the product arrives to be installed?
There is definitely some truth there since all natural linoleum flooring that was made with flaxseed oil has a natural amber hue to it when it is first made. When exposed to sunlight it’s color changes and it loses much of its amber hue. For instance, many of the blue colors will look green initially and when the amber-yellow cast fades they become the true blue color of the samples. A lot of folks get totally freaked out by this but it is not necessary to get crazy and the color will definitely change over time.
Are Marmoleum Click Tiles and Planks easy to install?
When the product comes out of its boxes and is allowed to acclimate for 24 to 48 hours, it has become stable in its final dimensions and is ready to install. Starting with one row against the long wall is an easy way to start. Once that row is complete and blocked into place, you can start to add complete rows by tipping them into place. No tools are necessary except maybe some wedges to hold them up at an angle prior to snapping into place. It is important that the products finished surfaces touch each other perfectly before it is pressed down into place. While the general practice is slightly different than the official Forbo Marmoleum Installation Guide, few people have trouble installing this flooring. Generally, a jigsaw can make all the cuts but a tablesaw, chop saw or handsaw may come in handy in different situations. Undercutting door jambs and trim and using shoe moldings at the perimeter will make for the most professional installation.
How can I get the best deal on natural flooring products?
Many local flooring stores do not carry Marmoleum but if it is available locally, we are sure that the local stores will appreciate your business. Be sure to contact us before a purchase to find the best price and to get an estimated time of arrival for your product and a stock check accross our 4 warehouses.
Is Marmoleum click cheap?
Marmoleum click is cheap or inexpensive when your calculating installation costs into the mix. It can be installed in many different configurations and can be installed like any other floating floor.
New Click II with the brown core fits tighter together than the old green core Click Classic which needed to be installed with a tapping block and a hammer while the new click does not and is tool-less. In fact, using a hammer and block of wood can damage Click II pretty easily. Seaming on the new Click II is so tight it is hard to see where the product joints are once it is installed. On the odd chance you found some quantity of Click Classic it WILL NOT marry up with the Click II.
How do I estimate the cost of flooring materials?
Measure carefully, being sure to have 5 or 10% overage for square patterns and maybe some more for diagonal patterns as an allowance for cutting and waste. You can use graph paper to lay out the design and count the exact square footage or number of pieces when you are estimating tile projects. Here are some tips:
Click Tiles and Planks: At approximately 12″ x 12″ squares and 12″ x 36″ planks they are 7 pieces to the box, so boxes are approximately 7 square feet and 21 square feet. Loose pieces are generally not sold. Click can generally not be easily installed on 45 degree angles because of the way it locks together.
Glue Down Tiles: At approximately 13″ square, the exact number of tiles can be confusing if you are using graph paper with 12″ squares. MCT comes in boxes of 45 or 54 square feet and the thicker Dual Tile comes in boxes of 45 or 54 square feet but also in boxes of 9 for mix and match color floors. Also, available in 20″ tile the Dual Tile comes in boxes of 54 square feet as well.
Sheet Material: Not considered a DIY or novice product, 79″ wide sheet material estimating should be left up to the installer. Since the product is very, very heavy and must be handled with specialized equipment when taken off the truck, it is uncommon to order it without the installer involved.
NOTE: Be sure to leave yourself some extra when estimating since getting more product in the exact same color lot can sometimes be impossible.
What questions should I ask in order to find an installer?
There are no hard and fast rules, but it takes a certain person who has pride in their workmanship and in their abilities to be able to install Marmoleum. It also takes a person who has been trained in the Forbo school or who grew up under the wing of an old time lino mechanic, because the product can be very technically demanding to install. If an artisan has a respect for math and science then they will be much better technicians, since there is really no way to get lucky or to fake it when installing linoleum products. Setting index lines, making patterns, having the right tools, knowing how to scribe fit and heat welding are all elements of the job that take a lot of practice to get right.
Can I install any of the three types of Marmoleum myself?
MARMOLEUM CLICK: This product is very similar to the other floating floor products on the market but with a few small exceptions. The Click II does not install with a tapping block and hammer, in fact if you try you will damage the product and it may leave bulges in the seams that can not be un-done. The floor is installed best by installing it in full and complete rows with the first few being the most important. They must, when completed be blocked in place with solid spacers against the walls and at the ends to prevent the beginning portion from moving. It is also critical to come back when you are done and remove those spacing blocks at the perimeter so the floor can float horizontally.
Being a “tool-free” installation means that each of the rows are simply slipped into the row before it but up at an angle. When the row being installed is raised up and the linoleum faces from the rows meet, the product will engage and snap together simply by pushing down. It is VERY important to only push down once the pieces are tight up against each other which may require a little practice or the help of a patient and adaptable helper. Really only one person can lead the click-in process and it must be gradually and carefully to prevent damaging the material. After two or three rows, people become experts. Undercutting door jambs and trim, cutting the L and flag shaped pieces around doorways, locating field seams when necessary and snapping in the very last piece of the puzzle take some head scratching and can perplex the impatient installers.
GLUE DOWN TILES: A little different than installing traditional VCT, PVC, Cork or Rubber Tiles, Marmoleum Tiles must be done in a very simple but specialized manner. They must be installed into the WET adhesive so people who install VCT are usually surprised that the floor installation fails in a few days because they ASSUMED it was the same. The other thing that is different is the need to use a 100 LB Roller rather than a 50, 60 or 75 lb roller that is typical in the industry. You can download plans to build your own 100LB Roller for free here.
SHEET GOODS: A trained installer is usually the best bet when you want to install Marmoleum Sheet Material. Master Mechanics are actually often able to do some remarkable art work in the Marmoleum medium like water cut patterns, inlays, borders, stripes and swirls. Lots of folks who are not trained can figure out how to install the floor themselves by reading the Marmoleum Glue Down Flooring Installation Guide and watching the videos. Knowing how to use scribing tools and how to make patterns can make the job a lot easier. I would absolutely not like to see beginners trying to heat weld themselves because it is so specialized and best left to the pros.
What is the best way to maintain Marmoleum Flooring?
Keeping a linoleum floor swept with a fine broom and spot cleaning occasionally is all that is needed for the most part. Many folks confess to hardly ever washing their floors entirely. It is really quite remarkable that the floor does not get dirty as fast as other flooring products because the linseed oil has a naturally bacteriostatic negative charge that prevents many things from adhering to the floor. Using a capful of Forbo PH Balanced cleaner and a damp mop is all that is necessary when the floor accumulates enough mess to require thorough cleaning.
The introduction of TopShield II has brought a much more durable floor finish for Marmoleum onto the market, even for commercial spaces. Floors installed before 2013 will usually have TopShield I and may require that the finish be reapplied every few years depending on the amount of traffic and the level of care the floor receives. People have had to reapply their finish each year and other people have their floors down for 10 or 15 years with it still looking new. It all depends on the amount of care and traffic. It is far better than the wax and periodic stripping that was common for linoleum back in the first half of the century.
Can I find Marmoleum at Home Centers like Lowes, Home Depot, Walmart or Menards?
Big Box stores don’t sell Marmoleum.
Is Marmoleum good for countertops?
Linoleum is very commonly used as a countertop for desks, libraries and spaces where cutting on the counter would not be a temptation. While it is durable as a floor surface it may not be right for a kitchen counter for most folks, although many have learned to care for it and be careful with it and they enjoy a beautiful countertop aesthetic.
Can Marmoleum be used for wall paneling or wainscoting?
Absolutely, in fact many people have used the 12″ x 36″ click type planks as wall paneling below a chair rail. Hospitals will also often “flash cove” Marmoleum up the walls to create and easy to mop joint where the floor meets the walls. Fast food businesses across the country are putting the product in many of their dining areas as a sustainable building product option.
Can I repurpose Marmoleum?
Repurposing is a major element in Green Building and Sustainable Living. Marmoleum Click snaps up in a flash and can be installed and removed over and over. Many companies use the product as their flooring of choice in trade show booths for that reason.
People have also installed a new Click floor over a perfectly good apartment floor with the plan to take the floor up when they move.
Is Marmoleum OK to use in commercial buildings?
Many architects and designers specify Marmoleum for gymnasiums, hospitals , classrooms, treatment rooms, hallways, and offices. Durable, elegeant and natural it can be a great choice where all three are desired. The product will hold s up with a minimum amount of maintenance and can easily outlast linoleum and commercial carpet and in most cases it needs less maintenance.
Can I install borders and inlays in my floor?
From the simplest option which is to add a cut corner insert to a tile floor to the addition of some beautiful custom borders from Forbo, the product is designed to be customized and to stretch the imagination of the designers and architects. Dual Tiles and standard Sheet Marmoleum are also the same thickness and can be combined easily in the same design to open up even more choices. Heat Welding can be used to insert pin stripe elements and accents
Is Marmoleum a great kitchens?
The kitchen is the perfect place for forbo marmoleum. It’s waterproof easy to clean and is easier to maintain then traditional linoleum. It also has a softer tactile feel on your bare feet then traditional vinyl or linoleum floors.
Should I use Marmoleum in my bathroom?
Yes, It is waterproof and durable and can make an average bathroom into something special. While it may require the making of a patter to get the fit just right, or perhaps the need to remove and reinstall the toilet, it is worth it. It is important to note that Click floors are just not appropriate for wet areas and shower rooms.
Is Marmoleum the right flooring for my basement?
First off, no matter what flooring you are installing in your basement, you should do basic moisture testing with relative humidity or calcium chloride testing beforehand in order to eliminate the opportunity for mold, mildew and humidity to create an indoor air quality issue. 85% humidity is the threshold for Marmoleum.
How humid is too humid for Marmoleum installation?
Floors over 85% humidity generally require some form of mitigation which might be a simply paint on finish if levels are under 90% while levels up to 99% generally require a specialty contractor to apply epoxy based coatings and to then encapsulate that coating with a cementious skim coat. There are really no other methods right now on the market to deal with 85% or higher moisture contents.
Update 2015: Forbo now has come out with a 1195 adhesive that will allow installations over concrete floors with 11 pounds of vapor pressure and 95% humidity. While this product is a little spendy it combines moisture mitigation with the adhesive, combining steps and saving time and money.
Is Marmoleum cool for the living room or bedroom?
A beautiful and healthy option for your family and it can be combined with area rugs or throw rugs. Many people have chosen natural Marmoleum after they have a brush with bad allergies or asthma.
How long does Marmoleum last?
Some floors have lasted 35 years and are still in good condition. Forbo offers a full 25 year warranty on normal wear and tear
Do you have recommended cleaning products for your linoleum products?
Full cleaning and maintenance links can be found below
Forbo Mop On Restorer Commercial
Forbo Hydrogen Peroxide Cleaner
Forbo Commercial floor cleaner
Forbo Residential Floor Finish
Forbo marmoleum Neutral PH cleaner
Is Marmoleum easy to clean and will it hold up when if chemicals are spilled?
Forbo Marmoleum products are subject to indicative chemical/stain testing in accordance with European standards. The tests provide baseline information on the effects of short term exposure to chemicals after cleaning and should be used as a comparative guide.
If specific chemicals are of particular concern we would advise that the effects are checked by the client on a sample of the proposed colour and material in conditions representative of those that will be experienced in service.
Is your Bulletin Board paintable?
Yes. We would suggest using a water based emulsion paint, but would advise testing the application first for adhesion on a small sample of material. However, as the paint is going to be less flexible than the Bulletin Board, marks may remain visible in the paint layer.
Forbo makes so many awesome linoleum flooring products, how can I ever settle on just one?
Marmoleum Click: is the snap lock floating flooring that is perfect for any DIY installer with basic skills.
MCT Tile: is the thin linoleum tiles that just about anyone who has put down any tiles can manage.
Sheet Marmoleum: is the glue-down heavy duty linoleum that we have all come to love for the last 150 years.
The best part is that no matter what you select and for what specific application, they will all hold up well because virtually all their product’s surfaces are now coated with the revolutionary TopShield II finish.