AFM Safecoat New Wallboard Primer
$5.50
/
Product Features
- For New Wallboard, Drywall and Sheetrock
- Fast Curing, Flat Finish
- Covers 350-400 sq/ft per gallon
- Environmentally friendly - very low VOC, the lowest toxicity for a product of its type.
- Contains no formaldehyde or aromatic hydrocarbons.
- Fights indoor air pollution.
AFM Safecoat New Wallboard Primer HPV Low VOC
This premium quality, fast-curing, flat-finish primer provides a superior prime coat over interior surfaces such as new gypsum wallboard and textured sheetrock. It equalizes the absorption rate of topcoat paints over a variety of surfaces with different porosities and helps to eliminate decorating problems over textured sheetrock and tape joints on wallboard.Usage
AFM Safecoat Wallboard Primer may be used on most interior surfaces: drywall, ceilings, fully cured plaster and stucco.Safecoat Transitional Primer Benefits
- Unique molecular structure promotes strong penetration and mechanical adhesion.
- Environmentally friendly - very low VOC, the lowest toxicity for a product of its type.
- Tight polymer network makes an excellent sealer.
- Transitions oil-based surfaces to accept waterbased coatings.
- Good stain blocker, reduces bleed through.
- Low Odor.
- Contains no formaldehyde or aromatic hydrocarbons.
- Fights indoor air pollution.
Sizes
- 1 gallon.
- 5 gallon.
Coverage
One gallon covers approximately 300-400 based on surface porosity.Surface Preparation
Surfaces to be coated with Safecoat New Wallboard Primecoat should be sound and cleanedof dirt, grease, mildew and oil. Do not apply over existing wallpaper. Tape joints must be tight and sound. Spray texture
must be uniform and adhering properly
Application
May be applied with a brush, roller or airless sprayer. Use a high quality nylon brush. A quality roller cover with a nap height of 1/4” to 1/2” is recommended. (Note: highpile heights will add additional texture.) Airless spayers should have a 17/1000 to 21/1000 tip (reversible type is best). Onlya 30 mesh high pressure filter should be used. Use a painter’s mask when spraying. For full coverage application, overlap preceding application with 1/4 to 1/2 the fan width at a distance of 18” from surface. Do not apply on cold, damp days or if surface, container or air temperature is below 55 degrees.
Clean Up
Clean tools and equipment while they are still wet with a solution of SafeChoice Super Clean and warm water.DRYING/CURING TIME:
Under normal conditions, Safecoat New Wallboard Primecoat dries to touch in one hour and is re-coatable after 2-4 hours. Normal conditions include a dry surface, access to fresh air flow, moderate humidity, and temperatures above 55 degrees F. Thick application, high humidity or conditions other than normal will cause Safecoat to dry and cure more slowly
More Information about AFM New Wallboard Primer
- Weight 4.5 lbs
- Size 1 Gallon, 1 Quart, 2-ounce sample, 5 Gallon
Product Features
- For New Wallboard, Drywall and Sheetrock
- Fast Curing, Flat Finish
- Covers 350-400 sq/ft per gallon
- Environmentally friendly - very low VOC, the lowest toxicity for a product of its type.
- Contains no formaldehyde or aromatic hydrocarbons.
- Fights indoor air pollution.
AFM Safecoat New Wallboard Primer HPV Low VOC
This premium quality, fast-curing, flat-finish primer provides a superior prime coat over interior surfaces such as new gypsum wallboard and textured sheetrock. It equalizes the absorption rate of topcoat paints over a variety of surfaces with different porosities and helps to eliminate decorating problems over textured sheetrock and tape joints on wallboard.Usage
AFM Safecoat Wallboard Primer may be used on most interior surfaces: drywall, ceilings, fully cured plaster and stucco.Safecoat Transitional Primer Benefits
- Unique molecular structure promotes strong penetration and mechanical adhesion.
- Environmentally friendly - very low VOC, the lowest toxicity for a product of its type.
- Tight polymer network makes an excellent sealer.
- Transitions oil-based surfaces to accept waterbased coatings.
- Good stain blocker, reduces bleed through.
- Low Odor.
- Contains no formaldehyde or aromatic hydrocarbons.
- Fights indoor air pollution.
Sizes
- 1 gallon.
- 5 gallon.
Coverage
One gallon covers approximately 300-400 based on surface porosity.Surface Preparation
Surfaces to be coated with Safecoat New Wallboard Primecoat should be sound and cleanedof dirt, grease, mildew and oil. Do not apply over existing wallpaper. Tape joints must be tight and sound. Spray texture
must be uniform and adhering properly
Application
May be applied with a brush, roller or airless sprayer. Use a high quality nylon brush. A quality roller cover with a nap height of 1/4” to 1/2” is recommended. (Note: highpile heights will add additional texture.) Airless spayers should have a 17/1000 to 21/1000 tip (reversible type is best). Onlya 30 mesh high pressure filter should be used. Use a painter’s mask when spraying. For full coverage application, overlap preceding application with 1/4 to 1/2 the fan width at a distance of 18” from surface. Do not apply on cold, damp days or if surface, container or air temperature is below 55 degrees.
Clean Up
Clean tools and equipment while they are still wet with a solution of SafeChoice Super Clean and warm water.DRYING/CURING TIME:
Under normal conditions, Safecoat New Wallboard Primecoat dries to touch in one hour and is re-coatable after 2-4 hours. Normal conditions include a dry surface, access to fresh air flow, moderate humidity, and temperatures above 55 degrees F. Thick application, high humidity or conditions other than normal will cause Safecoat to dry and cure more slowly
More Information about AFM New Wallboard Primer
- Weight 4.5 lbs
- Size 1 Gallon, 1 Quart, 2-ounce sample, 5 Gallon