AFM Safecoat Deckote Concrete & Masonry Semi Gloss Floor Paint
Safecoat Deckote Concrete Floor Paint is a safe, non-toxic, high-performance, ready-to-use,
waterborne coating designed primarily for use on dimensionally stable floors and decks including
interior or exterior concrete, masonry, stone, and brick. It is ideal for walkways, breezeways,
tennis courts, patios, and playgrounds. Also suitable for properly primed metal (use a safer metal
primer such as Safecoat MetalCoat), and can be used on primed and properly prepared wooden surfaces
with varying degrees of success depending upon environmental conditions and the nature of use. Dries
quickly to a tough, monolithic satin sheen film for lasting protection on properly prepared
surfaces. Safecoat Deckote is virtually odorless on application and is available in bases for
tinting to a wide variety of colors. It is compatible with other Safecoat sealers and coatings to
provide additional finish protection, durability and appearances, and worn areas are easy to recoat
and repair.
Size
Coverage
Approximately 350 square feet per gallon in one coat depending on surface porosity.
Surface Preparation
Remove any loose or peeling paint and scuff sand the surface (to create surface profile). All
surfaces must be clean, sound, dry, and free of any dirt, dust, oil, wax, grease, mildew, mold, and
other contaminants and debris before applying AFM Safecoat Deckote. New cementitious surfaces should
age at least thirty days and have a pH below 10 before coating. Scrub surface with a solution of
SafeChoice Safety Clean and water. Use 2-6 oz. of SafeChoice Safety Clean per gallon of water.
Triple rinse to assure cleaner is completely removed. For the best adhesion on smooth surfaces with
no surface profile, acid-etching may be required, followed by completely neutralizing the surface.
Use extreme caution when working with acid and follow label and MSDS precautions. All acid residual
must be removed prior to coating. Surface pH should be 7-10 for best results. Test surface porosity
and profile by dropping water onto dry surface. If water drops fail to penetrate quickly, surface
may need additional attention to create proper surface profile. Test for surface cleanliness by
applying a strong tape (such as duct tape) to the cleaned areas and pull back up. The tape must be
clean and free of any concrete dust or dirt. If particles or a white residue are still present,
remove them completely with additional scrubbing, rinsing, and possibly etching.
Application
Intermix (boxing) all cans of the same color to ensure color uniformity before applying. The surface
should be completely dry before application. Always have adequate ventilation. Before using, stir
well, then apply as is with a high quality nylon or synthetic bristle brush, pad applicator,
sprayer, or roller of appropriate nap (3/8” nap recommended). Apply in two or more uniform, thin
coats. Cross-roll to avoid lap-marks and holidays. Use an airless sprayer, minimum 2000 p.s.i., with
a .015-.017 tip. Use a 60 mesh filter. Always use a painter’s mask when spraying. For best results,
this product should not be reduced. Use only during low or moderate humidity conditions. This
product is NOT recommended for use on unprimed wood, unprimed metal, vitreous surfaces, surfaces
with little to no surface profile, or areas subject to severe hydrostatic pressure or standing
water. Use product when air and surface temperature are between 50 - 90° F (10 - 32°C). Do not apply
outside if the threat of rain or heavy humidity is imminent within 72 hours of application. Two
coats are normally sufficient for most jobs. Additional cure time may be necessary if more than two
coats are applied. Note: these instructions are intended to be general only and not exhaustive. The
applicator should determine what preparation and techniques are best suited to the specific surface.
Caution
COATED SURFACES MAY BECOME SLIPPERY WHEN WET. A slip-resistant floor finish additive is available to
help prevent slip if desired. Adding a slip resistant additive may reduce the life span of the
product in heavy traffic areas.
Clean-Up
Clean tools and equipment while they are still wet with a solution of SafeChoice Super Clean and
warm water. If Safecoat DecKote is allowed to harden on tools, it will be necessary to use lacquer
thinner or stronger solvents.
Drying/Curing Time
Under normal conditions, Safecoat Deckote dries to touch in 4-12 hours. Allow 24 hours between
coats. Normal conditions include a dry surface, access to fresh air flow, moderate humidity, and
temperatures above 55°F. Safecoat Deckote can be put into service in 12 - 24 hours under most
conditions, but will develop its full durability in 3 weeks after applying. Avoid heavy traffic and
cleaning for a minimum of 7 days.
More Information about AFM Safecoat Deckote Concrete & Masonry Semi Gloss Floor Paint
