Oregon Shepherd’s made-in-the-USA 40-pound loose sheep wool insulation blow box may be blown in, or placed by hand.
Loose Sheep Wool insulation allows you to fully fill an enclosed cavity, so you will generally achieve a slightly higher R-value, for example, R-21.9 for a 5.5″ deep wall cavity as opposed to R19 for batt or roll insulation.
This product is a mix of raw sheep wool from U.S. sheep farms, and pre-consumer recycled content from natural woolen mills (textile scraps, no synthetic dyes included). The percentages of raw wool and recycled content vary over time depending upon input streams.
Here is a blog from one of our customers who set out on a journey of home maintenance full of investigation, research, and surprises resulting in a holistic approach to renovation: Love Laugh and Make Lemonade – How to Knit Your House a Sweater
Here is a link to a raw loose sheep wool insulation that is a bit more expensive ($6.30/# compared to $4.48/#) because it is 100% raw wool made in America https://eco-buildingproducts.com/product/havelock-wool-insulation-loose-sheep-wool/
Here is a link to a raw sheep wool insulation batt made in USA that is more expensive but is manufactured in a 48″ batt that is available in 16″ on center and/or 24″ on center width in either R13 and R20 values. https://eco-buildingproducts.com/product/havelock-wool-insulation-sheep-wool-insulation/ As you may already know installing batts in vertical applications is much easier than blowing loose wool into vertical wall cavities.
Here is a link to a smaller 5# box ,if a 40# box is more than desired. https://eco-buildingproducts.com/product/oregon-shepherd-loose-sheep-wool-insulation-craft-box/
- 165 square feet at R13 (modern 16″ on-center 2×4 construction, or 3.5″ deep)
- 105 square feet at R19 (modern 16″ on-center 2×6 construction, or 5.5″ deep)
- 77 square feet at R30 (modern 16″ on-center 2×8 construction, or 7.5″ deep)
Netting may be included at a nominal cost to hold wool in place.
The intended installation density is about one pound per cubic foot for attics/ceilings/floors (horizontal cavities) and up to 1.2 lbs. per cubic foot for walls (vertical cavities).
This product comes compacted at about a 6-to-1 ratio, so you will need to fluff it. A standard insulation blower will do this for you. Otherwise it can be tricky to get the advertised coverage when fluffing manually.
If placing by hand:
- You may want to order a little extra, as it is trickier to get the proper density
- Your wool arrives in a box packed to about 6 times the installation density, so each cubic foot of packed wool will need to be ‘fluffed’ to about six cubic feet.
- One trick is to put portions of the wool in a large plastic bag and using a shop-vac on reverse, insert the nozzle into the bag and fluff the wool.
When blowing in loose sheep wool:
- You can expect a 10 foot projection of the material from the end of the hose.
- There is not much that you have to do differently for sheep wool versus fiberglass/cellulose:
- Sheep Wool is more dense than fiberglass and cellulose.
- Don’t run your airlock wide-open. Keep it about 2/3rds open.
- Run your air wide open.
- Don’t attempt to dense pack with any hose diameter smaller than 2″.
- The folks at InsulationMachines.net recommend the CM2400 for sheep wool.
- However, John mentioned that they prefer the FibreForce blower by Intec for the best application.
Wall, ceiling, and floor insulation is often used as a component of soundproofing. Any insulation product will improve your soundproofing compared to a hollow cavity.
However, if you are attempting to address a serious sound control problem that is impacting health or relationships with family or neighbors, you will want to educate yourself on the intricacies of sound control problems and the corresponding solutions. We recommend you start by visiting our friends at the Soundproofing Company as they are the industry experts.
Sheep Wool Insulation Prices
Sheep Wool Insulation Prices