Sale!

AFM Safecoat WaterShield Low VOC Sealant

Rated 5.00 out of 5 based on 1 customer rating
(1 customer review)

$5.00$227.75

Product Features

  • non toxic, lead free, Formaldehyde free and no Mildewicides or fungicides
  • Fast drying – 10 minutes
  • interior and exterior use
  • bonds to  concrete, stucco, brick, block, terrazzo, unglazed tile and wood
  • adds protection to Afm Safecoat Durostain increasing it’s water Repellency
  • Apply one coat with brush, roller, lambswool applicator or low pressure spray.

Click here to see how Safecoat seals toxic chemicals.

Clear

Description

Description

AFM Safecoat WaterShield Low-VOC Water Repellent Sealer

Safecoat WaterShield is a clear, versatile, controlled-penetration low VOC water repelling sealer, which provides an invisible barrier against water and resists oils, grease and similar liquids. WaterShield is non-toxic, non-flammable, lead-free and formaldehyde-free, and does not contain surface contaminating silicones, making it a desirable coating for interior or exterior use. May be used on painted surfaces and may be painted over when dry. Dries clear and does not discolor. Contains 2g/l VOC content. Safecoat’s WaterShield has excellent adhesion and is easy to apply. In addition to sealing and providing a protective barrier against water migration, WaterShield helps to harden, dust-proof and control efflorescence in masonry surfaces.

Usage

Safecoat WaterShield can be used on porous, cementitious materials such as concrete, stucco, brick, block, terrazzo and unglazed tile. Can also be used to add water repellency to exterior vertical wood siding when applied over AFM Safecoat DuroStain.

Sizes

  • 1 gallon.
  • 5 gallon.

Maintenance

For surfaces originally treated with AFM Safecoat WaterShield, consider using AFM Safecoat WaterStop.

Specs

Coverage

One gallon of Safecoat WaterShield covers approximately 250-300 square feet in one coat depending on method of application and surface porosity. Thinning: no reduction is required.

Surface Preparations

All surfaces must be clean, dry, free from dust, dirt, loose sand, mildew, efflorescence or any other foreign matter. The pH of the material to be sealed must be as close to neutral as possible, and definitely below 10. If the surface has been acid washed, for example to remove efflorescence, it must be thoroughly clean water rinsed and neutralized. Similarly, once mildew has been removed, for example by washing with chlorinated household bleach, the surface must be thoroughly rinsed with water and all bleach residue removed. Always use care with bleach and acid, and be sure to read and follow all warnings, label instructions and MSDS. Power wash, brush or scrape all surfaces and we sure to have a good, sound substrate before application of Safecoat WaterShield. Repair cracks, holes and repaint concrete block if necessary.

WARNING: Caution must be used when removing coating from existing surfaces. Surfaces should be checked for lead content. Sanding may create dust or dust particles that may contain lead, a hazardous substance. Avoid the creation and breathing of any dust particle. Always wear protective equipment. Breathing or eating lead containing dust or debris can cause health problems, especially in children or pregnant women.

Application

Always use adequate ventilation. Apply one coat with brush, roller, lambswool applicator or low pressure spray. When applying on vertical surface, start at the lower level and spray upwards. Flood until Safecoat WaterShield runs to assure complete saturation. On horizontal surfaces allow to sit for about ten minutes and remove any excess. Try to avoid puddling. Note: before using, check with water on test areas to be sure there is penetration. If there is none, do not use. Note: these instructions are intended to be general only and not exhaustive. The applicator should determine which preparation and techniques are best suited to the specific surface.

Clean Up and Curing

Clean tools and equipment while still wet with a solution of SafeChoice Super Clean and warm water. Drying/Curing Time: Under normal conditions, Safecoat WaterShield dries within two hours and cures hard in 24 hours. Normal conditions include a clean, dry surface, access to fresh air flow, a dust free environment, moderate humidity and temperatures above 55 degrees F. Thick application, high humidity or conditions other than normal will cause Safecoat WaterShield to dry and cure more slowly.

More Information about AFM Safecoat WaterShield

Additional information

Weight 0.9
Size

, ,

1 review for AFM Safecoat WaterShield Low VOC Sealant

  1. Rated 5 out of 5

    Fast Shipping. Thanks Eco!

Add a review

Your email address will not be published. Required fields are marked *