AFM Safecoat DuroTone water based wood stain
AFM Safecoat DuroTone water based wood stain is a premium quality fast curing low odor semi-transparent interior wood stain. DuroTone is ideal for interior and exterior wood surfaces using no aromatic solvents, formaldehyde, UV inhibitors or Hazardous Air Pollutants. It has excellent pigmentation stability and is a durable stain. For use on all wood surfaces. DuroTone contains no aniline dyestuffs, no gilsonite or asphalt, no aromatic solvents and no formaldehyde. Low VOC Formula 28 g/l
Safecoat DuroStain is recommended for unsealed wooden surfaces. Note: staining large surfaces such as floors with a water-based stain requires significant expertise and is not recommended for the average user.
Safecoat Durotone Benefits
- Excellent, light fast pigmentation stability
- Combination of non-toxic dye and pigment creates better color retention and coverage.
- Addition of dye to formulation means DuroTone has less water-based characteristics (lap lines, splotching etc..)
- Safely used by and for the chemically sensitive.
- No acrylic means its more receptive to top coat penetration.
- Low odor, non-offensive to installer and occupant .
- Very low VOC content, meets or exceeds all federal and state air quality regulations, including California
- Very low VOC content (28 g/l)
1 quart, 1 gallon, and 2-ounce samples
One gallon of Safecoat Durotone covers approximately 450 square feet in one coat depending on surface porosity and the intensity of the stain color desired.
More Information about AFM Safecoat Durotone
Duroton e is available in these colors:
Stains may be mixed together to modify color. Durotone is also available as a clear finish.
NOTE: Safecoat Durostone uses natural mineral pigments and slight variation in color may accordingly occur between batches. Always use material from the same batch for a specific job.
Because of wide variations in the way different woods accept stain, we particularly recommend that users always test in small, inconspicuous areas for appearance and compatibility before application to the entire surface. Surfaces to be stained with Safecoat Durotone should be sound and cleaned or dirt, dust, grease, wax, silicone, soap and oil, and must be completely free of mold, mildew or fungus contamination. Cleaning with an odorless, dye-free, all-purpose cleaner like SafeChoice Super Clean is recommended. Previously painted or sealed surfaces will not accept stain readily. Consequently, stripping of old paint or sealer followed by rinsing and sanding will be required before application of Safecoat Durotone to achieve maximum penetration from this product. Surface can be dampened with water to assist user in getting an even application. Porous woods with strong grain pattern can be tamed by using thinned (50% with water) application of Safecoat Durotone Clear. Safecoat Durotone can be used as a glaze over painted and sealed surfaces.
Always have adequate ventilation. Intermix (boxing) all containers of the same color to ensure uniformity before applying. Before using, stir Safecoat Durotone well, then apply it evenly without reduction using a high quality nylon or synthetic bristle brush. To adjust intensity of color, best results will be obtained by staining six foot sections (2′ x 3′) of the surface and wiping off excess stain while it is still wet to achieve the desired intensity of color. Always keep a wet edge. Darkness of stain may be increased by high surface porosity, wiping off less stain, or letting the stain dry longer before wiping. A squeegee applicator can be beneficial when coating large flat surfaces like doors. The shade of the stained surface will be affected by the color and type of wood. Reduce if desired for spraying with up to 1/2 pint of water per gallon. Always use a painter’s mask when spraying. Do not apply in direct sunlight. Make sure to wipe off any excess stain which does not penetrate into the wood. Note: these instructions are intended to be general only and not exhaustive. The applicator should determine what preparation and techniques are best suited to the specific surface.
Under normal conditions, Safecoat Durotone dries to touch in one hour and is re-coatable after two hours. Normal conditions include a dry surface, access to fresh air flow, moderate humidity and temperatures above 55 degrees F. Thick application, high humidity or conditions other than normal will cause Safecoat to dry and cure more slowly. Clean tools and equipment while they are still wet with a solution of SafeChoice Super Clean or SafeChoice Safety Clean and warm water.